solution below is to resolve the issue of plain paper printing with wrinkles or
creases. If you only experience this issue when printing on envelopes or thick
paper, refer to the solution - "The
envelopes come out creased or wrinkled? How can I correct it?"
Check that paper is loaded into the paper tray correctly:
Remove the paper tray completely from the machine.
Remove the paper from the tray and set the green paper guides (1) to the correct
will be necessary to hold the release levers when moving the guides to a larger
release lever for the left and right guides is located at the middle of the
release lever for the rear guide is in the middle of the rear guide.
Make sure that the rear guide does NOT push tightly against the paper. It should
be set to the position marked for the paper size that will be loaded into the
tray. If the rear guide is pushed too tightly against the rear edge of the
paper, the paper may be unable to feed properly.
Fan the paper well to avoid paper jams or misfeeds and then load the paper in
not overfill the tray. The maximum paper level is marked on the right paper
guide with a red line with three arrows pointing at it.
the printer is used infrequently, turn over the stack of paper in the paper
tray. Also, try rotating the paper 180° in the paper tray.
Put the paper tray firmly back into the machine.
Make sure you use paper that meets the recommended paper
following media types, sizes, weights and capacities meet the recommended
specifications for this printer:
paper: Xerox 4200DP 20 lb or Hammermill Laser Paper 24 lb
paper: Paper that meets DIN 19309 specifications
Avery laser label #5160
Paper 20 - 28 lbs.
Paper 16 - 28 lbs.
Paper 16 - 43 lbs.
Paper 16 - 20 lbs.
Paper 28 - 43 lbs. (used in MP tray only)
Types and Sizes:
paper tray can use the following paper types: Plain paper, recycled paper, bond
paper, thin paper, transparency
paper tray can use the following paper sizes: Letter, Legal, Executive, Folio,
A4, A5, A6, B5 (ISO), B6 (ISO)
MP tray can use the following paper types: Plain paper, recycled paper, bond
paper, thin paper, transparency, thick paper, envelopes, labels
MP tray can use the following paper sizes: Width: 2.75 to 8.5 in. and Length:
4.57 to 16 in.
paper that is made for plain paper copying.
paper that is 20 to 24 lb (75 to 90 g/m2).
neutral paper, do not use acidic or alkaline paper.
long grain paper.
paper with a moisture content of approximately 5%.
This printer can use recycled paper that meets DIN 19309 specification. Do not
use inkjet paper as this might cause a paper jam or damage your
you use paper other than the ones recommended, the paper could jam, misfeed,
wrinkle or crease.
Open the front cover and remove the drum and toner.
Check the interior of the machine any debris or scraps of paper.
the toner cartridge from the drum by holding down the green lock lever on the
right side of the drum unit and lifting the toner out.
Handle the toner cartridge carefully. If toner scatters on hands or clothing,
immediately wipe it off or wash it with cold water.
Check the drum unit for any debris or scraps of paper.
Reinstall the toner cartridge into the drum unit until you hear it lock into
place. If you put it in properly, the lock lever will lift automatically.
Reinstall the toner and drum assembly into the machine and close the front
Resend the print job.
the page prints out normally, discontinue trouble shooting.
the page print out with wrinkles or creases, continue to the next
Open the rear cover.
Resend the print job.
If this corrects the issue, discontinue troubleshooting.
If the paper continues to come out wrinkled, continue to the next
Try using new paper from a fresh ream.
the problem continues and your machine is within warranty, you can locate a
Brother Authorized Service Center (ASC) in your area by clicking on the link
contact Brother Customer Service by calling 1-877-Brother (1-877-276-8437)
Monday through Friday, excluding holidays.
your machine is out of warranty, you can locate a Brother Authorized Service
Center using the information listed above.