Recently I was in a popular store strolling down the baby aisle. Seeing so many little baby things inspired me! I decided to create something that could be included in a special gift set for a new baby. Along with a lot of other must have baby items, I saw some very boring baby bottles and envisioned dressing up plain baby bottles with embroidery. I hope you enjoy this bottle cover project. It would be great included in a basket full of additional baby basics! Gather up a few simple supplies, pick an adorable baby design, and you can create a cute, quick cover for a basic baby bottle in no time at all. Are you ready? Let's go sew!

Materials and Supplies

Note: Choose a design that will easily fit on the front area of the bottle. The design featured on this baby bottle is part of an adorable collection of Morango Designs in a category called Button Babies.
You'll find this design and many other coordinating Button Baby motifs available from the Brother iBroidery.com download center.
Below are examples of both baby girl and baby boy designs. Either of these is ideal for decorating the front of a bottle cover.

Happy Baby Girl:


  • Size 2.94 inches X 3.90-inches
[caption id="attachment_14713" align="aligncenter" width="295"]Baby Bottle Cover Happy Girl[/caption]

Happy Baby Boy:
  • Size 3.09 inches X 3.90-inches
[caption id="attachment_14712" align="aligncenter" width="295"]Baby Bottle Cover Happy Boy [/caption]

Steps to Create Bottle Cover

  1. Prepare fabric piece for bottle cover as follows:
  • Measure bottle height beginning at the bottom and continuing to the point where bottle tapers inward. Add 1-inch hem allowance to this measurement and record as HEIGHT.
  • Measure the width by loosely wrapping tape measure around bottle. Add 1-inch seam allowance to this measurement and record as WIDTH. See example in Figure #1a and Figure #1b.
[caption id="attachment_14700" align="aligncenter" width="800"]Baby Bottle Cover Figure #1a[/caption] [caption id="attachment_14701" align="aligncenter" width="800"]Baby Bottle Cover Figure #1b[/caption]
  • Using guidelines above, in this example the bottle cover piece will measure 7-inches HIGH X 8 1/2-inches WIDE.
  1. Once you determine your bottle cover size you'll need to add a few extra inches so the hoop is fully filled with fabric prior to embroidering. Measure to make sure you have enough fabric and then cut an oversized piece to prepare for embroidering. Layer fabric with tear-away stabilizer and embroider design in center of fabric piece using desired thread colors.
Tip: If you're including other gifts with a particular color scheme you may want to alter the original thread colors to coordinate with your additional items. See Figure #2.
[caption id="attachment_14702" align="aligncenter" width="800"]Baby Bottle Cover Figure #2[/caption]
  1. With embroidery design in the center, trim piece to bottle cover size and remove excess stabilizer.
  2. Set up machine for sewing. Finish all four raw edges of the pre-quilted fabric piece. I used the 'G" foot and a basic overcast stitch for a clean finish. You could also use your serger to finish edges. See Figure #3a and Figure #3b.
[caption id="attachment_14723" align="aligncenter" width="214"]Baby Bottle Cover Figure #3a[/caption] [caption id="attachment_14703" align="aligncenter" width="800"]Baby Bottle Cover Figure #3b[/caption]
  1. Turn and press under a ½” hem for the bottom and a ½” casing for the elastic at the top of the cover. Attach pin or bodkin to one end of elastic. See Figure #4.
[caption id="attachment_14704" align="aligncenter" width="800"]Baby Bottle Cover Figure #4[/caption]
  1. Wrap elastic around the neck of the bottle to determine size. Pin, leaving an extra inch or so at each end. Mark location of the pin at each end and cut excess elastic. See Figure #5.
[caption id="attachment_14705" align="aligncenter" width="800"]Baby Bottle Cover Figure #5[/caption]
  1. Insert elastic through top casing, pulling until you reach the markings. Pin to temporarily hold elastic in place. See Figure #6.
[caption id="attachment_14706" align="aligncenter" width="800"]Baby Bottle Cover Figure #6[/caption]
  1. Next, sew the center back seam of the cover, backstitching at each end and stitching a second time over elastic to make sure it is secure. See Figure #7.
[caption id="attachment_14707" align="aligncenter" width="800"]Baby Bottle Cover Figure #7[/caption]
  1. Trim away excess elastic. Press seam allowance open. Tack seam allowances down at top and bottom with hand or machine stitches. Turn cover right side out and slip over bottle. See front and back of cover in Figure #8a and Figure #8b.

You are finished! Enjoy!

[caption id="attachment_14708" align="aligncenter" width="800"]Baby Bottle Cover Figure #8a[/caption] [caption id="attachment_14709" align="aligncenter" width="800"]Baby Bottle Cover Figure #8b[/caption]

Options and ideas:

  • Embroider “It’s a Boy”, “It’s a Girl”, another short saying, or add the baby’s name to customize the cover.
  • Add washable trims or ribbons to further decorate the cover.
  • Decorate burp cloths or bibs with coordinating Button Baby motifs. Consider bundling all items together and tie with a pretty bow for a great gift presentation!

Comments (9)
img
Joanne Banko Says:
4/14/2018 7:53:47 PM

Hello Susan! It was great to get your note! Thanks for the kind comments :-) You are right about using the idea as a springboard for other bottle covers - good thinking!!! Happy Sewing!

Reply To Joanne Banko

Your email will not be published. Required fields are marked with *

img
Joanne Banko Says:
4/14/2018 7:55:28 PM

Hey Christy! So glad to know this project got your creative juices flowing :-) Have fun stitching my friend!

Reply To Joanne Banko

Your email will not be published. Required fields are marked with *

img
Joanne Banko Says:
4/11/2018 4:17:15 PM

Hi Pat! Thank you for your comment! More babies?!? How wonderful! I'm sure you'll create lasting memories with baby gifts crafted with your own two hands!

Reply To Joanne Banko

Your email will not be published. Required fields are marked with *

img
Janice Ferguson Says:
4/9/2018 2:01:29 PM

How cute is this!!! Including this in a basket with other baby items would make such a unique and welcome shower gift. Another great Joanne Banko idea, as always.

Reply To Janice Ferguson

Your email will not be published. Required fields are marked with *

img
Pat Guerin Says:
4/11/2018 6:35:05 AM

Just love the cute bottle idea, have two babies on the way will surely make a unique addition for a baby gift! Thanks, Joanne

Reply To Pat Guerin

Your email will not be published. Required fields are marked with *

img
Susan T Says:
4/12/2018 1:28:04 PM

Once again, you are so darn creative, Joanne! I enjoy your projects/ideas so much. I can see using this on sippy cups and water bottles with sports motifs, monograms, etc. Thanks so much for sharing.

Reply To Susan T

Your email will not be published. Required fields are marked with *

img
Gail Beam Says:
4/8/2019 3:53:04 AM

Thank you for the neat tutorial for the bottle cover

Reply To Gail Beam

Your email will not be published. Required fields are marked with *

img
Joanne Banko Says:
4/11/2018 4:10:43 PM

Thanks for the note Janice! It is really nice to have "go to" gift ideas that make a gift priceless.

Reply To Joanne Banko

Your email will not be published. Required fields are marked with *

img
Christy pocek Says:
4/12/2018 3:57:28 PM

Well, you are just the inspirational person I need right now!!! What a cute idea🍼🍼

Reply To Christy pocek

Your email will not be published. Required fields are marked with *

Leave a Comment

Your email will not be published. Required fields are marked with *