Free Design: Hugs & Kisses Pillowcase

Sew up some love by decorating a pillowcase with this ‘Love Never Fails’ Free Design from Brother. For a unique trim, add striped piping to compliment the contrast band with SA150,
the Brother Pearls and Sequins Foot. Learn this technique and you’ll want to repeat it on many other projects. For a neat finish, I stitched this sweet pillowcase using a popular roll up method for the band and then used enclosed seams for the sides and bottom. This pillowcase looks perfect on the outside and inside too! Are you ready? Let’s go sew!

Materials and Supplies

  • Brother
    sewing and embroidery machine. Machine used in this example is the XP1 Luminaire. Any Brother machine with a 5-inch X 7-inch hoop is fine for embroidering this design.
  • Brother
    Embroidery Thread, Bobbin Thread, and size 11 embroidery needle for embroidering.
  • SA150
    Pearls and Sequins Foot for creating striped piping.
  • SA5810
    Brother medium weight tear-away stabilizer.
  • Basic sewing notions including thread to match fabric and a removable marker or chalk.
  • One package of pre-purchased ½-inch wide Maxi Piping.
  • Brother FREE Design of the Month: Free Design_Feb_2020_Love never Fails.pes
    . See Figure #1.

Fabrics for Pillowcase:

  • Fabric A: Print fabric for pillowcase: Using the full width of the fabric from selvedge to selvedge, cut one piece of fabric 28 ½-inches long. Note: Choose a print that looks good horizontally or vertically. In this example I designated one specific edge for the top, so that the lettering on the fabric would correspond to the embroidered lettering on the band.
  • Fabric B: Solid fabric for pillowcase band: Using the full width of the fabric from selvedge to selvedge, cut one oversized piece measuring 12-inches long. Note: If your fabric is lightweight fuse a piece of featherweight interfacing to the wrong side of the entire piece.
[caption id="attachment_23400" align="aligncenter" width="800"] Figure #1[/caption]

Please read fabric and sizing notes before you begin:

  • The average size for a ready-made, standard pillowcase measures approximately 21-inches Wide X 32-inches Long. Measurements and yardage in this example are for a standard size pillowcase. Finished length is approximately 32-inches. By cutting each piece using the full width of the fabric, the finished width is determined by the actual width of the fabric. Trim away the selvedge edge of each piece and then make sure Fabric A and Fabric B are both cut to equal the same width. If you want your pillowcase to have a tighter fit on the pillow you can trim away some of the width. Seam allowance is ¼-inch for the band, and 5/8-inch for the side and bottom seam of the pillowcase.
  • For larger pillows such as king size, consider measuring a ready-made pillowcase and then cut your fabrics accordingly.
  • This rollup style of making a pillowcase has been popular for several years. You may have heard it called the “burrito” sewing method, due to the way the band is sewn to the main piece. Oftentimes, you’ll find pillowcase instructions listing ¾ yard for fabric A and ¼ yard for fabric B. This results in a slightly shorter pillowcase and does not allow for the oversized piece used for embroidering the band. In my experience fabric is rarely cut evenly and usually skews slightly after laundering. I prefer to purchase extra yardage and have a little excess to trim. I like to purchase 7/8 yard for Fabric A and 3/8 yard for Fabric B. This allows for pre-shrinking and straightening the fabric ends which are often uneven after laundering.

Here are the basic steps for making the pillowcase:

  • Determine desired pillowcase size and cut fabrics accordingly.
  • Embroider oversized band of fabric and trim to size.
  • Create striped piping and baste to top edge of pillowcase fabric.
  • Roll up pillowcase, layer with folded band, and stitch band seam.
  • Turn right side out and sew enclosed seams to finish sides and bottom.

Steps to Create Pillowcase

1. Gather your supplies. See Figure #2. [caption id="attachment_23401" align="aligncenter" width="800"] Figure #2[/caption] 2. Transfer design to machine and decide on thread colors. I changed my colors to coordinate with my fabric. See Figure #3 below: [caption id="attachment_23402" align="aligncenter" width="800"] Figure #3[/caption] 3. Mark fabric band for embroidery by finding the vertical center of half of the band, and then measure and mark horizontal center 5 ½-inches from the top edge. I made a simple template by cutting a piece of paper 3-inches high X 7-inches wide, to roughly match the size of the design. Then I taped it to the fabric and used it as a temporary marking. After lining up the center of the template with the center of the hoop I removed the template. Note that the arrow points to the top edge of the band. Layer fabric band with tear away stabilizer and hoop so that center markings line up with center of hoop. See Figure #4a, Figure #4b, and Figure #4c. [caption id="attachment_23403" align="aligncenter" width="800"] Figure #4a[/caption] [caption id="attachment_23404" align="aligncenter" width="800"] Figure #4b[/caption] [caption id="attachment_23405" align="aligncenter" width="800"] Figure #4c[/caption] 4. Embroider design. See Figure #5. [caption id="attachment_23406" align="aligncenter" width="800"] Figure #5[/caption] 5. Remove excess stabilizer and press piece. To trim band to size needed for pillowcase begin by measuring and marking a line 9 ½-inches from the top, embroidered edge. Cut band along the line. 6. To create striped piping, set up machine for sewing with embroidery thread in the top and bobbin. Attach the pearls and sequins foot. Select a plain blanket stitch using a long stitch length and a width set to cover the piping. The stitch featured in this example is Luminaire stitch No. 9-29, width 6.0, length 4.3. I mirror imaged the stitch to sew the blanket stitch on the right-hand side of the piping. Tip: If you have a machine with the Brother My Custom Stitch feature you can create a wide blanket stitch very easily. See options and ideas at the end of these instructions for more information. 7. Place piping under the channel in the foot and stitch across the piping with the right and left swing of the stitch forming over the piping cord, and the straight stitches running alongside the piping. See Figure #6a and Figure #6b. [caption id="attachment_23407" align="aligncenter" width="800"] Figure #6a[/caption] [caption id="attachment_23408" align="aligncenter" width="800"] Figure #6b[/caption] 8. Since we are using such a small seam allowance for the band it’s a good idea to overcast the top raw edge of the pillowcase piece. Attach presser foot “J”, the standard presser foot, and change thread to match pillowcase fabric. Stitch along the edge with a narrow three step zig zag. See Figure #7a. Next, baste edge of piping to secure it to the top edge. See Figure #7b. [caption id="attachment_23409" align="aligncenter" width="800"] Figure #7a[/caption] [caption id="attachment_23410" align="aligncenter" width="800"] Figure #7b[/caption] 9. Lay the band on a flat surface with the right side facing up. Starting from the bottom and working toward the top, roll the pillowcase piece so it will fit within the folded band in the next step. Tip: I like to roll the fabric around a yardstick and then remove it after rolling. See Figure #8. [caption id="attachment_23411" align="aligncenter" width="800"] Figure #8[/caption] Place the rolled pillowcase piece over the embroidered band with right sides facing and piped edge along top edge of band. See Figure #9a and Figure #9b. [caption id="attachment_23412" align="aligncenter" width="800"] Figure #9a[/caption] [caption id="attachment_23413" align="aligncenter" width="800"] Figure #9b[/caption] 10. Fold band piece and pin so rolled pillowcase is sandwiched in between, and the right side of the band is facing the wrong side of the piped edge. See Figure #10. [caption id="attachment_23414" align="aligncenter" width="800"] Figure #10[/caption] 11. Change to the piping foot and select a straight stitch. Place rolled piece under the foot, with piping firmly underneath the channel in the foot. Adjust the needle position so the stitching line is snug against the piping. You’ll want to stitch using a seam allowance of approximately ¼-inch. I used a setting of 5.5. See enhanced photo with stitching line in Figure #11. Tip: As an alternative you could switch to an adjustable zipper/cording foot for this step. [caption id="attachment_23415" align="aligncenter" width="800"] Figure #11[/caption] 12. Sew the top edge of the pillowcase to both layers of the band, making sure that you’re stitching through just the three pinned layers, and taking care that the rolled pillowcase piece is not caught in the seam. 13. Now, begin the process of pulling the pillowcase through the band, easing the pillowcase through the tube formed by the stitched band. This will take a bit of effort but eventually the whole piece will magically turn through the opening. See Figure #12. [caption id="attachment_23416" align="aligncenter" width="800"] Figure #12[/caption] 14. Give the piece a good pressing. To finish the pillowcase neatly, you’ll want to sew enclosed seams, otherwise known as French seams on the side and bottom. To reduce bulk before sewing the seam, use tweezers to pull out and trim away a ½-inch piece of cording at each end. See Figure #13. [caption id="attachment_23417" align="aligncenter" width="800"] Figure #13[/caption]

Follow instructions below for sewing the enclosed seam:

  • Pin side seams with wrong sides together. See Figure #14.
[caption id="attachment_23418" align="aligncenter" width="800"] Figure #14[/caption]
  • Sew a scant ¼-inch seam along the side. See Figure #15.
[caption id="attachment_23419" align="aligncenter" width="800"] Figure #15[/caption]
  • Trim any loose threads. Press seam flat and then pin with right sides together. See Figure #16.
[caption id="attachment_23420" align="aligncenter" width="800"] Figure #16[/caption]
  • Sew the second seam using a 3/8-inch seam allowance, fully enclosing the first one. See Figure #17.
[caption id="attachment_23421" align="aligncenter" width="800"] Figure #17[/caption]
  • Repeat steps for an enclosed bottom seam. Turn pillowcase right side out and press.

You are finished! Enjoy!

Options and Ideas:

  • Take a look at our Quick Tip for this month and you’ll find instructions for creating a simple blanket stitch using the exclusive Brother My Custom Stitch feature found on many machine models.
  • As an alternative to cutting the band oversized, you can use the trimmed size of 9 ½-inches and attach the band to adhesive backed stabilizer for the embroidery.
  • Other trim such as rick rack, lace, or a contrast fabric strip can serve as a substitute for the piping if you wish.
  • Feb_2020_Hugs & Kisses Pillowcase PDF