Answer to your Frequently Asked Question:

 
Printer Friendly
Description of Problem 100000017466

On a Macintosh, how do I configure the wireless printer and install the printer driver WITHOUT a cable?


Description of Solution 200000022298

STEP I: Gather the wireless network settings of your wireless access point or wireless router

 

Gather the following wireless network settings of your access point or router.  Refer to the access point's user guide for instructions on accessing the network settings information.  

 

SSID or Network Name

The name of your Wireless Network or Access Point

Authentication Method

Open System, Shared Key, WPA/WPA2-PSK*

Encryption Mode

None, WEP, TKIP, AES

Network Security Key (Password)

Encryption Key, WEP Key, Passphrase

 

*NOTE: The Brother machine only supports WPA2-PSK with AES.  If you are using WPA2-PSK with TKIP you will receive a connection error.

 

If you do not have the network settings information or cannot find this information, refer to the solution -  How do I find the Wireless Security Information on my Wireless Macintosh OSX computer? 

 

If you need to contact your router manufacturer for assistance gathering the required information, refer to the following link to obtain contact information for common router manufacturers: 

http://www.brother-usa.com/support/wireless/wireless_router_information.htm 

 

STEP II: Perform a factory reset on the printer network card

 

1. Turn off the printer.

2. Make sure that the front cover is closed and the power cord is plugged in.

3. Hold down Go as you turn on the power switch. Keep Go pressed down until all the LEDs light up and then Status LED turns off.

4. Release Go. Make sure that all the LEDs are off.

5. Press Go six times. Make sure that all the LEDs light up to indicate the print server has been reset to its factory default settings. The printer will restart.

STEP III: Enable the Wireless Network Card

 

1.  With the printer power turned on and the printer Ready, hold down the GO button for about 15 seconds. Release the GO button when the printer prints a Network Configuration page.

 

2.  Locate the Node Type at the top of the page.

 

- If the Node Type is Brother NC-7600w, IEEE 802.11b/g (Active), go to STEP 3

 

- If the Node Type is Brother NC-7600w, IEEE 802.11b/g (Inactive) or Brother NC-6800h, Ethernet 10/100BASE-TX (Active), you will need to enable the wireless network card again, repeat STEP III.

 

3.  Wait 1 minute. It is very important to wait 1 minute after the reset before continuing. If you do not wait at least 1 minute, the Brother machine may not have enough time to reset.

 

4.  Print the Printer Settings by pressing the GO button 3 times.

 

5.  Locate the IP Address in the middle and the Comm. Mode and Name (SSID) near the bottom. Verify:

 

a. IP Address of the printer is a 169.254.x.x number.

 

 

 

 

b. Comm Mode is Ad-hoc.

 

c. Name (SSID) is SETUP.

 

 

 

 

d. If the IP Address is not a 169.254.x.x number, the Comm Modes is not Ad-hoc, and the Name (SSID) is not SETUP, you will need to reset the printer network card and enable the wireless network card again, start again from STEP II.

 

STEP IV: Communicate to the printer WITHOUT a network cable and configure the wireless settings

 

1. To communicate with the printer in Ad-hoc mode, the wireless computer needs to join the printer's SETUP network.

 

NOTE: If you are using a third party utility to manage your wireless connections, contact the manufacturer for assistance with the following steps.

 

2. If you are using the Macintosh operating system to manage your wireless connections, use the following steps:

 

a. In the Airport Wireless Utility, connect to SETUP.

 

 

    

b. The wireless icon will turn gray.

 

 

 

STEP V: Configure the Wireless Network Card

 

1. Open a web browser.  An error message will appear informing you are not connected to the internet. 

 

2. Enter the IP Address of the printer into the web browser screen and press ENTER.  The Brother Web Management screen will appear.

 

 

3.  Click on Network Configuration near the top of the screen. (Figure 3).

 

 

4.  A login screen will appear. Enter the following:

Username: admin

Password: access

 

Then click OK.

 

 

5. Click Configure Wireless near the middle of the screen. (Figure 4).

 

 

6. Change the Communication Mode to Infrastructure. (Figure 5).

 

7. Click the BROWSE button next to the Wireless Network Name (SSID). (Figure 5).

 

 

8. Select the Name (SSID) for your network and click OK (Figure 6). Refer to the network settings information gathered in STEP I.

 

 

9. Leave the Channel setting as is.

 

10. Select the appropriate Authentication Method from the drop down list (Figure 7). Refer to the network settings information gathered in STEP I.

 

 

11.  Select the appropriate Encryption Method (Figure 8). Refer to the network settings information gathered in STEP I.

 

 

NOTE: If WEP is selected as the Encryption Method, enter the hex code for the WEP Key 1. There is no need to enter the Passphrase for WEP Encryption.

 

NOTE: If using an Authentication Method other than Open or Shared is selected, then a Passphrase must be entered on the Passphrase line (Figure 9).

 

 

 

 

12. Click Submit to update the printer with your wireless settings (Figure 10).

 


 

13.  A screen indicating the settings have been updated successfully should appear.  (Figure 11). The printer wireless network card is now Active on the network.  

 

 

14. Switch your computer BACK to your wireless access point or wireless router, rather than the SETUP network. If you need assistance doing this, please refer back to the start of STEP IV.

 

15. Verify the printer is now attached to the wireless access point or wireless router:

 

a. Wait 1 minute. It is very important to wait 1 minute before continuing. If you do not wait at least 1 minute, the Brother machine may not have enough time to join the network and receive an IP address.

 

b. Print the Printer Settings by pressing the GO button 3 times. Look at the last page of the Printer Settings.

 

c.  Locate the IP Address in the middle and confirm it is assigned via DHCP. (Figure 12).

 

 

d. Locate the Comm Mode near the bottom and confirm it is set to Infrastructure. (Figure 13).

 

e. Locate the Name (SSID) near the bottom and confirm it matches your access point or router. (Figure 13).

 

f. Locate the Wireless Link Status near the bottom and confirm it reads Link OK. (Figure 13).

 

 

NOTE: If the IP Address is 0.0.0.0, wait another minute and print out the settings pages again. If the IP Address is still 0.0.0.0, please reset the router by powering it off, then back on. Also, turn the printer off, then back on. Wait approximately one minute. Print out the Network Settings page again and verify the settings. If the IP Address is still a 0.0.0.0 number, please verify your security information in STEP I is correct and start again from STEP II.

 

If the IP Address is a 169.254.x.x number and the Wireless Link Status in LINK OK, please check your router for MAC filtering. If MAC filtering is enabled, please enter the MAC address to the list.  If MAC filtering is not enable, please reset the router by powering it off, then back on. Also, turn the printer off, then back on. Wait approximately one minute. Print out the Network Settings page again and verify the settings. If the IP Address is still a 169.254.x.x number, please verify your security information in STEP I is correct and start again from STEP II.

 

If the IP Address is a 169.254.x.x number and the Wireless Link Status in FAILED TO ASSOCIATE, please reset the router by powering it off, then back on. Also, turn the printer off, then back on. Print out the Network Settings page again and verify the settings. If the IP Address is still a 169.254.x.x number, please verify your security information in STEP I is correct and start again from STEP II.

 

The printer is now configured and is operating on your network.

 

STEP VI: Printer Driver Installation

 

If you are using Macintosh OS 10.6 or higher or you do not have the Brother software CD, refer to solution - How do I download and install the CUPS driver for Macintosh OS X? 

 

If you have the Brother software CD and are using Macintosh OS 10.3 - 10.5, refer to the solution - The printer is configured on a wired or wireless network. How do I install the printer driver on a Macintosh 

Was this helpful?
Please help us to improve our services by letting us know if this information was helpful: